Vintage-cellars Evolution 162 Bottle Wine Rack Manuel d'utilisateur télécharger pdf (Page 2)

4. Afx the Second Panel – Carefully lift and rotate the partially

assembled unit to rest on the panel with the unsecured ends

upright, like a bed of nails. Lay the second panel on the ends of the

E1’s and one at a time, align each E1 with the corresponding hole

and secure it in place with an E1-SCREW (Fig. A.). If assembling

a multi-section unit, use the E1-STUD instead (Fig. B.). It is

recommended that the E1’s be secured row-by-row working down

the panel, as this will allow the easiest alignment of the E1 with

the holes. For single section units, the assembly is complete, skip

to Step 6.

Tip: The E1-STUD’s may be quickly screwed in by gently tightening

them in the chuck of a drill with approximately 3/4 of the stud

exposed, screwing them in until the at spot in the middle of the

stud is just below the surface of the panel and then releasing the

end of the stud from the chuck.

Lifetime Warranty

Wine Master Cellars, LLLP (WMC) warrants to the original consumer-purchaser that

this product shall be free from defects in workmanship and materials under normal

and reasonable use for the lifetime of the product. WMC will, at its option, renish or

replace any product or part found to be defective during the warranty period and excludes

installation charges, shipping costs, and the cost of removal and reinstallation. WMC may

require you to return the part(s) claimed to be defective, for its inspection - freight or

postage prepaid.

This warranty does not include the cost of any inconvenience or property damage

due to the failure of the product and does not cover damage due to Devine Act, third

party act out of the control of WMC, misuse, abuse, accident, or damage arising out of

transportation of this product. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL

OTHER OBLIGATIONS, LIABILITIES OR WARRANTIES AND THERE IS NO WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

In no event shall WMC be liable or responsible for INCIDENTAL OR CONSEQUENTIAL

DAMAGES or for any other direct or indirect damage, loss, cost, expense, or fee. Neither

the WMC distributor nor the retail establishment selling this product has any authority

to make any warranties or to promise remedies in addition to or inconsistent with those

stated above. WMC’s maximum liability, in any event, shall not exceed the purchase price

of the product paid by the original consumer-purchaser.

All matters regarding the sale of the product or this warranty shall be governed by the

laws of the state of Colorado and the exclusive jurisdiction of and venue for any warranty

claims or claims directly or indirectly related to the sale of the product shall be Colorado.

Any claim, or action relating the purchase of the product or this warranty must be led

no more than six (6) months after the date the claim arose. All statute of limitations to

the contrary are waived.

Some states do not allow the exclusion or limitation of incidental or consequential

damages. In such case, the above limitations or exclusions may not be applicable. This

warranty gives you specic legal rights and you may also have other rights which vary

from state to state.

Please call us toll free at 866-650-1500 for assembly assistance or to request replacement parts.

www.VintageView.com

5. Attach the E1’s to Exposed Studs (for Extensions only) –

With all of the studs installed, begin securing the panel in place

by installing E1’s along the top, middle and bottom rows. Once

the second panel is rmly locked in place, the unit may be stood

upright for ease of access while installing the remaining E1’s.

Tip: The E1’s may be quickly installed by gently tightening one end

of the tube in the chuck of a drill and screwing the other end onto

the exposed E1-STUD. Remember to keep the drill set at a low

torque so as not to overtighten or damage anything.

6. Secure to Wall – It is highly recommended that all units be

secured to a wall for optimal stability. This may be accomplished

by either directly fastening a panel to the wall by pre-drilling a

hole through the panel and screwing or bolting into the wall or by

using an “L” bracket. Please contact your VintageView dealer for

information regarding brackets of custom shapes or sizes.

Fig. A Fig. B

1 2

Commentaires sur ces manuels

Pas de commentaire

Vintage-cellars Evolution 162 Bottle Wine Rack Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Vintage-cellars Evolution 162 Bottle Wine Rack